Nissan Rogue Service Manual: DTC/Circuit diagnosis
- Trouble diagnosis - specification value
- Power supply and ground circuit
- U0101 CAN comm circuit
- U1001 CAN comm circuit
- U1040 ENG comm circuit
- U1044 ENG comm circuit
- U1050, U1051 LIN communication
- P0011 IVT control
- P0014 EVT control
- P0031, P0032 A/F sensor 1 heater
- P0037, P0038 HO2S2 heater
- P0075 intake valve timing control
- P0078 EVT control solenoid valve
- P0101 MAF sensor
- P0102, P0103 MAF sensor
- P0111 IAT sensor
- P0112, P0113 IAT sensor
- P0116 ECT sensor
- P0117, P0118 ECT sensor
- P0122, P0123 TP sensor
- P0125 ECT sensor
- P0127 IAT sensor
- P0128 thermostat function
- P0130 A/F sensor 1
- P0131 A/F sensor 1
- P0132 A/F sensor 1
- P0137 HO2S2
- P0138 HO2S2
- P0139 HO2S2
- P014C, P014D, P015A, P015B, A/F sensor 1
- P0171 fuel injection system function
- P0172 fuel injection system function
- P0181 FTT sensor
- P0182, P0183 FTT sensor
- P0196 EOT sensor
- P0197, P0198 EOT sensor
- P0222, P0223 TP sensor
- P0300, P0301, P0302, P0303, P0304 misfire
- P0327, P0328 KS
- P0335 CKP sensor (POS)
- P0340 CMP sensor (phase)
- P0420 three way catalyst function
- P0441 EVAP control system
- P0443 EVAP canister purge volume control solenoid valve
- P0444, P0445 EVAP canister purge volume control solenoid
- P0447 EVAP canister vent control valve
- P0448 EVAP canister vent control valve
- P0451 EVAP control system pressure sensor
- P0452 EVAP control system pressure sensor
- P0453 EVAP control system pressure sensor
- P0456 EVAP control system
- P0460 fuel level sensor
- P0461 fuel level sensor
- P0462, P0463 fuel level sensor
- P0500 VSS
- P0506 ISC system
- P0507 ISC system
- P050A, P050B, P050E cold start control
- P0520 EOP sensor
- P0524 engine oil pressure
- P052A, P052B intake valve timing control
- P0603, P062F ECM
- P0604 ECM
- P0605 ECM
- P0606 ECM
- P0607 ECM
- P060A ECM
- P060B ECM
- P0643 sensor power supply
- P0850 PNP switch
- P1078 EVT control position sensor
- P1148 closed loop control
- P117A air fuel ratio
- P1212 TCS communication line
- P1217 engine over temperature
- P1225 TP sensor
- P1226 TP sensor
- P155D generator
- 1564 ASCD steering switch
- P1568 signal invalid
- P1572 brake pedal position switch
- P1574 ASCD vehicle speed sensor
- P1715 input speed sensor
- P1805 brake switch
- P2004 intake manifold runner control valve
- P2014, P2016, P2017, P2018 intake manifold runner control valve position sensor
- P2096, P2097 A/F sensor 1
- P2100, P2103 throttle control motor relay
- P2101 electric throttle control function
- P2118 throttle control motor
- P2119 electric throttle control actuator
- P2122, P2123 APP sensor
- P2127, P2128 APP sensor
- P2135 TP sensor
- P2138 APP sensor
- P2610 ECM internal timer
- Brake pedal position switch
- Cooling fan
- Electrical load signal
- Fuel injector
- Fuel pump
- Ignition signal
- Information display (ASCD)
- Malfunction indicator lamp
- On board refueling vapor recovery (ORVR)
- Refrigerant pressure sensor
- Sensor power supply2 circuit
How to erase permanent DTC
Description
OUTLINE
When a DTC is stored in ECM
When a DTC is stored in ECM and MIL is ON, a permanent DTC is erased with MIL
shutoff if the same malfunction
is not detected after performing the ...
Trouble diagnosis - specification value
Description
The specification (SP) value indicates the tolerance of the value that is
displayed in “SPEC” of “DATA MONITOR”
mode of CONSULT during normal operation of the Engine Control Sy ...
Other materials:
ECU diagnosis information
BCM
Reference Value
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following
functions. Refer to the Signal Tech II
User Guide for additional information.
Activate and display TPMS sensor IDs
Display tire pressure reported by the TPMS sensor
Read T ...
DTC/circuit diagnosis
POWER SUPPLY AND GROUND CIRCUIT
AUDIO UNIT
AUDIO UNIT : Diagnosis Procedure
Regarding Wiring Diagram information, refer to AV-27, "Wiring Diagram".
1.CHECK FUSE
Check that the following fuses are not blown.
Are the fuses blown?
YES >> Replace the blown fuse after repairing t ...
P050A, P050B, P050E cold start control
Description
ECM controls ignition timing and engine idle speed when engine is started
with pre-warming up condition.
This control promotes the activation of three way catalyst by heating the
catalyst and reduces emissions.
DTC Description
DTC DETECTION LOGIC
DTC No.
CONSULT scre ...
