Nissan Rogue Service Manual: P1715 input speed sensor
Description
ECM receives input speed sensor signal from TCM through CAN communication line. ECM uses this signal for engine control.
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms (Trouble diagnosis content) | DTC detecting conditio |
| P1715 | IN PULY SPEED (IN PULY SPEED) | Input speed sensor signal is different from the theoretical value calculated by ECM from output speed sensor signal and engine rpm signal. |
POSSIBLE CAUSE
- Harness or connectors (The CAN communication line is open or shorted.)
- Harness or connectors (Input speed sensor circuit is open or shorted.)
- TCM
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P1715 is displayed with DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or P060B, first perform the trouble diagnosis for DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or P060B.
Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".
NO >> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.
- Turn ignition switch OFF and wait at least 10 seconds.
- Turn ignition switch ON.
- Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
- Start engine and drive the vehicle at more than 50 km/h (31 MPH)
for at least 5 seconds.
CAUTION: Always drive vehicle at a safe speed.
- Check 1st trip DTC.
Is 1st trip DTC detected? YES >> Proceed to EC-416, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis Procedure
1.CHECK DTC PRIORITY
If DTC P1715 is displayed with DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or P060B, first perform the trouble diagnosis for DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or P060B.
Is applicable DTC detected?
YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".
NO >> GO TO 2.
2.CHECK DTC WITH TCM
Check DTC with TCM. Refer to TM-47, "CONSULT Function".
Is the inspection result normal? YES >> GO TO 3.
NO >> Perform trouble shooting relevant to DTC indicated.
3.REPLACE TCM
Replace TCM. Refer to TM-202, "Removal and Installation".
>> INSPECTION END
P1574 ASCD vehicle speed sensor
Description
The ECM receives two vehicle speed sensor signals via CAN communication line.
One is sent from combination
meter, and the other is from TCM (Transmission control module). The ECM uses ...
P1805 brake switch
DTC Description
DTC DETECTION LOGIC
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P1805
BRAKE SW/CIRCUIT
(BRAKE SW/CIRCUT)
A stop ...
Other materials:
Warning systems switch (if so equipped)
Warning systems switch (if so equipped)
The warning systems switch is used to turn on
and off the warning systems (Lane Departure
Warning (LDW), Forward Collision Warning
(FCW) and Blind SpotWarning (BSW) systems)
that are activated using the settings menu on the
vehicle information displa ...
Radiator
Exploded View
REMOVAL
Reservoir tank
Reservoir tank cap
Reservoir tank hose
Mounting rubber (upper)
Radiator cap
Radiator
CVT fluid cooler hose
Clamp
CVT fluid cooler hose
Mounting rubber (lower)
O-ring
Drain plug
...
Lifting point
Special service tool
The actual shapes of Kent-Moore tools may differ from those of special
service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
LM4086-0200
( - )
Board on attachment
LM4519-0000
( - )
Safety stan ...
