Nissan Rogue manuals

Nissan Rogue Service Manual: P2014, P2016, P2017, P2018 intake manifold runner control valve position sensor

Nissan Rogue Service Manual / Engine / Engine Control System / DTC/Circuit diagnosis / P2014, P2016, P2017, P2018 intake manifold runner control valve position sensor

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition
P2014 IN/MANIFOLD RUNNER POS SEN B1 (Intake manifold runner position sensor/ switch circuit bank 1) An excessively low voltage from the sensor is sent to ECM.
P2016 IN/MANIFOLD RUNNER POS SEN B1 (Intake manifold runner position sensor/ switch circuit low bank 1)
P2017 IN/MANIFOLD RUNNER POS SEN B1 (Intake manifold runner position sensor/ switch circuit high bank 1) An excessively high voltage from the sensor is sent to ECM.
P2018 IN/MANIFOLD RUNNER POS SEN B1 (Intake manifold runner position sensor/ switch circuit intermittent bank 1)

POSSIBLE CAUSE

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

1.CHECK DTC PRIORITY

If DTC P2014, P2016, P2017 or P2018 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-379, "DTC Description".

NO >> GO TO 2.

2.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1.  Turn ignition switch OFF and wait at least 10 seconds.
  2.  Turn ignition switch ON.
  3.  Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION: Before performing the following procedure, confirm that battery voltage is more than 11 V at idle. >> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE

  1.  Start engine and let it idle for 10 seconds.
  2.  Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-424, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK DTC PRIORITY

If DTC P2014, P2016, P2017 or P2018 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-379, "DTC Description".

NO >> GO TO 2.

2.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR POWER SUPPLY

  1. Turn ignition switch OFF.
  2.  Disconnect intake valve manifold runner control valve position sensor harness connector.
  3.  Turn ignition switch ON.
  4.  Check the voltage between intake valve manifold runner control valve position sensor harness connector.

Check intake manifold runner control valve position sensor power supply

Is the inspection result normal? YES >> GO TO 5.

NO >> GO TO 3.

3.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR POWER SUPPLY CIRCUIT

Check the voltage between intake valve manifold runner control valve position sensor harness connector and ground.

Check intake manifold runner control valve position sensor power supply circuit

Is the inspection result normal? YES >> GO TO 4.

NO >> Perform the trouble diagnosis for power supply circuit.

4.CHECK ECM GROUND CIRCUIT

  1. Turn ignition switch OFF.
  2.  Disconnect ECM harness connector.
  3.  Check the continuity between ECM harness connector and ground.

Check ECM ground circuit

  1. Also check harness for short to power.

Is the inspection result normal? YES >> GO TO 8.

NO >> Repair or replace error-detected parts.

5.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.
  2.  Disconnect ECM harness connector.
  3.  Check the continuity between intake manifold runner control valve position sensor harness connector and ECM harness connector.

Check intake manifold runner control valve position sensor ground circuit

  1. Also check harness for short to power.

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace error-detected parts.

6.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR INPUT SIGNAL CIRCUIT

  1.  Check the continuity between intake manifold runner control valve position sensor harness connector and ECM harness connector.

Check intake manifold runner control valve position sensor input signal circuit

  1. Also check harness for short to ground and to power.

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace error-detected parts.

7.CHECK INTERMITTENT INCIDENT

Perform GI-41, "Intermittent Incident".

Is the inspection result normal? YES >> Replace intake manifold assembly. Refer to EM-26, "Exploded View".

NO >> Repair or replace error-detected parts.

8.CHECK INTERMITTENT INCIDENT

Refer to GI-41, "Intermittent Incident".

>> INSPECTION END

P2004 intake manifold runner control valve
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P2004 TUMBLE CONT/V (Intake manifold runner contro ...

P2096, P2097 A/F sensor 1
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P2096 POST CATALYST FUEL TRIM SYS B1 (Post catalys ...

Other materials:

Cylinder block
Exploded View Cylinder block  Top ring  Second ring  Oil ring  Snap ring Piston  Connecting rod Piston pin Connecting rod bearing  Rear oil seal  Reinforcement plate  Drive plate  Signal plate  Pilot convert ...

P0444, P0445 EVAP canister purge volume control solenoid
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P0444 PURG VOLUME CONT/V (Evaporative emission system purge control valve circuit open) An excessively low voltage signal is sent to ECM through ...

Unit disassembly and assembly
REAR DRIVE SHAFT Exploded View DISASSEMBLY Circular clip Dust shield Slide joint housing Snap ring Spider assembly Boot band Boot  Shaft Circular clip  Joint sub-assembly  Sensor rotor : Wheel side Disassembly and Assembly DISASSEMBLY Final Dri ...

В© 2014-2026 Copyright t32.nirogue.com