Nissan Rogue Service Manual: P050A, P050B, P050E cold start control

Nissan Rogue Service Manual / Engine / Engine Control System / DTC/Circuit diagnosis / P050A, P050B, P050E cold start control

Description

ECM controls ignition timing and engine idle speed when engine is started with pre-warming up condition.

This control promotes the activation of three way catalyst by heating the catalyst and reduces emissions.

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen terms (Trouble diagnosis content)	DTC detecting condition
P050A	COLD START CONTROL (Cold start idle air control system performance)	ECM does not control engine idle speed properly when engine is started with pre-warming up condition.
P050B	COLD START CONTROL (Cold start ignition timing performance)	ECM does not control ignition timing properly when engine is started with pre-warming up condition.
P050E	COLD START CONTROL (Cold start engine exhaust temperature too low)	The temperature of the catalyst inlet does not rise to the proper temperature when the engine is started with pre-warming up condition.

POSSIBLE CAUSE

Lack of intake air volume
Fuel injection system
ECM

FAIL-SAFE

P050A

Traveling control mode (Accelerator angle variation control)

P050B, P050E

Not applicable

DTC CONFIRMATION PROCEDURE

1.CHECK DTC PRIORITY

If DTC P050A, P050B or P050E is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".

NO >> GO TO 2.

2.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION: Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE-1

With CONSULT

Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Select “DATA MONITOR” mode with CONSULT.
Check the indication of “COOLAN TEMP/S”.

With GST

Follow the procedure “With CONSULT” above.

Is the value of “COOLAN TEMP/S” between 15°C (59°F) and 36°C (97°F)? YES >> GO TO 4.

NO-1 [If it is below 15°C (59°F)]>>Warm up the engine until the value of “COOLAN TEMP/S” reaches 15°C (59°F) or more. Retry from step 1.

NO-2 [If it is above 36°C (97°F)]>>Cool engine down to less than 36°C (97°F). Retry from step 1.

4.PERFORM DTC CONFIRMATION PROCEDURE-2

With CONSULT

Set the select lever in N range.
Start the engine and warm up in idle with the value of “COOLAN TEMP/S” between 15°C (59°F) and 40°C (104°F) for more than 15 seconds.
Check 1st trip DTC.

With GST

Follow the procedure “With CONSULT” above.

Is 1st trip DTC detected? YES >> Proceed to EC-357, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK DTC PRIORITY

If DTC P050A, P050B or P050E is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".

NO >> GO TO 2.

2.PERFORM IDLE AIR VOLUME LEARNING

Perform EC-141, "Work Procedure".

Is Idle Air Volume Learning carried out successfully? YES >> GO TO 3.

NO >> Follow the instruction of Idle Air Volume Learning.

3.CHECK INTAKE SYSTEM

Check for the cause of intake air volume lacking. Refer to the following.

Crushed intake air passage
Intake air passage clogging
Clogging of throttle body

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace malfunctioning part

4.CHECK FUEL INJECTION SYSTEM FUNCTION

Perform DTC Confirmation Procedure for DTC P0171. Refer to EC-260, "DTC Description".

Is the inspection result normal? YES >> GO TO 5.

NO >> Proceed to EC-261, "Diagnosis Procedure" for DTC P0171.

5.PERFORM DTC CONFIRMATION PROCEDURE

Turn ignition switch ON.
Erase DTC.
Perform DTC Confirmation Procedure.

See EC-356, "DTC Description".

Is the 1st trip DTC P050A, P050B or P050E displayed again? YES >> Replace ECM. Refer to EC-499, "Removal and Installation".

NO >> INSPECTION END

P0507 ISC system

Description The ECM controls the engine idle speed to a specified level through the fine adjustment of the air, which is let into the intake manifold, by operating the electric throttle control ac ...

P0520 EOP sensor

DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P0520 EOP SENSOR/SWITCH (Engine oil pressure senso ...

Other materials:

C1105, C1106, C1107, C1108 wheel sensor
DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes C1105 RR RH SENSOR-2 When distance between rear wheel sensor RH and rear wheel sensor RH rotor is large. When installation of rear whe ...

General maintenance
Explanation of General Maintenance General maintenance includes those items which should be checked during the normal day-to-day operation of the vehicle. They are essential if the vehicle is to continue operating properly. The owners can perform the checks and inspections themselves or have ...

P0447 EVAP canister vent control valve
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P0447 VENT CONTROL VALVE (Evaporative emission system vent control circuit open) An improper voltage signal is sent to ECM through EVAP canister ...