Nissan Rogue manuals

Nissan Rogue Service Manual: P0603, P062F ECM

Nissan Rogue Service Manual / Engine / Engine Control System / DTC/Circuit diagnosis / P0603, P062F ECM

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition
P0603 ECM BACK UP/CIRCUIT [Internal Control Module Keep Alive Memory (KAM) Error] ECM buck up system does not function properly.
P062F CONTROL MODULE (Internal control module EEPROM error) EEPROM (built-in microcomputer) system internal ECM does not function properly.

POSSIBLE CAUSE

DTC P0603

DTC P062F

ECM

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

Perform the following procedure before performing DTC Confirmation Procedure.

  1.  Turn ignition switch OFF and wait at least 10 seconds.
  2.  Turn ignition switch ON.
  3.  Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P062F

  1.  Start engine and wait at least 10 seconds.
  2.  Turn ignition switch OFF and wait at least 10 seconds.
  3.  Repeat steps 1 and 2 for 4 times.
  4.  Turn ignition switch ON.
  5.  Erase DTC.
  6.  Turn ignition switch OFF and wait at least 10 seconds.
  7.  Start engine and wait at least 10 seconds.
  8.  Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-371, "Diagnosis Procedure".

NO >> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P0603

  1.  Turn ignition switch OFF and wait at least 10 seconds.
  2.  Turn ignition switch ON and wait at least 10 seconds.
  3.  Turn ignition switch OFF and wait at least 5 minutes.
  4.  Turn ignition switch ON and wait at least 10 seconds.
  5.  Repeat steps 3 and 4 for 5 times.
  6.  Turn ignition switch ON.

7. Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-371, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.INSPECTION START

Check that the battery negative terminal is not disconnected during ignition switch ON.

Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.ERASE DTC

  1. Start the engine and let it idle at least 10 seconds.
  2.  Turn ignition switch OFF.
  3.  Repeat steps 1 and 2 for 4 times.
  4.  Erase DTC.
  5.  Turn ignition switch OFF and wait at least 10 seconds.
  6.  Start the engine and let it idle for 10 seconds.
  7.  Check 1st trip DTC.

Is DTC P062F detected again? YES >> Replace ECM. Refer to EC-499, "Removal and Installation".

NO >> INSPECTION END

3.CHECK ECM POWER SUPPLY AND GROUND CIRCUIT

Check ECM power supply and ground circuit. Refer to EC-165, "Diagnosis Procedure".

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace error-detected parts.

4.CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to GI-41, "Intermittent Incident".

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace error-detected parts.

5.PERFORM DTC CONFIRMATION PROCEDURE

  1.  Turn ignition switch ON.
  2.  Erase DTC.
  3.  Perform DTC confirmation procedure. Refer to EC-370, "DTC Description".

Is the DTC P0603 or P062F detected again? YES >> Replace ECM. Refer to EC-499, "Removal and Installation".

NO >> INSPECTION END

P052A, P052B intake valve timing control
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P052A CAMSHAFT POSITION TIMING B1 (Cold start “A ...

P0604 ECM
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P0604 ECM [Internal control module random access ...

Other materials:

Front seat
DRIVER SIDE DRIVER SIDE : Exploded View POWER SEAT Headrest  Seatback support  Seatback board  Seatback heater (if equipped)  Seatback trim  Seatback pad Seat cushion outer finisher (RH) Seat cushion rear finisher (RH) Seat cushion inner fini ...

Component parts
METER SYSTEM METER SYSTEM : Component Parts Location Vehicle front  View of the fuel pump and fuel level sensor inspection hole covers with the rear seat removed.  View of front engine assembly No. Component Function 1 Combination me ...

ECU diagnosis information
AUTOMATIC BACK DOOR CONTROL UNIT Reference Value VALUES ON THE DIAGNOSIS TOOL CONSULT MONITOR ITEM TERMINAL LAYOUT PHYSICAL VALUES Fail Safe DTC Inspection Priority Chart If some DTCs are displayed at the same time, perform inspections one by one based on th ...

© 2014-2026 Copyright t32.nirogue.com