Nissan Rogue Service Manual: P1212 TCS communication line
Description
This CAN communication line is used to control the smooth engine operation during the TCS operation. Pulse signals are exchanged between ECM and “ABS actuator and electric unit (control unit)”.
Be sure to erase the malfunction information such as DTC not only for “ABS actuator and electric unit (control unit)” but also for ECM after TCS related repair.
DTC Description
DTC DETECTION LOGIC
Freeze frame data is not stored in the ECM for this self-diagnosis.
| DTC No. | CONSULT screen terms (Trouble diagnosis content) | DTC detecting condition |
| P1212 | TCS/CIRC (TCS/CIRC) | ECM can not receive the information from “ABS actuator and electric unit (control unit)” continuously. |
POSSIBLE CAUSE
- Harness or connectors (CAN communication line is open or shorted.)
- ABS actuator and electric unit (control unit)
- Dead (Weak) battery
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P1217 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or P0607.
Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".
NO >> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
- Turn ignition switch OFF and wait at least 10 seconds.
- Turn ignition switch ON.
- Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION: Before performing the following procedure, confirm that battery voltage is more than 10.5V at idle. >> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE
- Start engine and let it idle for at least 10 seconds.
- Check 1st trip DTC.
Is 1st trip DTC detected? YES >> Proceed to EC-395, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis Procedure
Perform the trouble diagnosis for TCS. Refer to BRC-66, "Work Flow".
NOTE: If DTC P1212 is displayed with DTC UXXXX and/or P0607, perform the following trouble diagnosis.
- Trouble diagnosis for DTC UXXXX Refer to EC-93, "DTC Index".
- Trouble diagnosis for DTC P0607 Refer to EC-376, "DTC Description".
P117A air fuel ratio
DTC Description
DTC DETECTION LOGIC
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P117A
AIR FUEL RATIO B1
(AIR FUEL RATIO B1)
ECM ...
P1217 engine over temperature
DTC Description
DTC DETECTION LOGIC
If the cooling fan or another component in the cooling system malfunctions,
engine coolant temperature will
rise.
When the engine coolant temperature reache ...
Other materials:
B1428 seat belt buckle switch IH
Description
DTC B1428 SEAT BELT BUCKLE SWITCH LH
The air bag diagnosis sensor unit monitors the seat belt buckle switch LH
status. If the control unit detects an
open or short condition in the circuit, it will set the DTC.
PART LOCATION
Refer to SRC-6, "Component Parts Location".
D ...
Walk away lock function
When you walk away from the Nissan Rogue with the Intelligent Key, the vehicle will
be locked automatically by the walk away lock function (the operation range is
around 7 ft (2 m)). This function is disabled by default, but you can enable it
using the vehicle information display.
NOTE:
When the d ...
Starting the engine
Basic information
1. Apply the parking brake.
2. Confirm that the vehicle is in the P (Park) position.
The Intelligent Key must be inside the vehicle when operating the ignition switch. This is essential for proper system recognition on your Nissan Rogue.
3. Push the ignition switch to the ON po ...
