Nissan Rogue manuals

Nissan Rogue Service Manual: P2119 electric throttle control actuator

Nissan Rogue Service Manual / Engine / Engine Control System / DTC/Circuit diagnosis / P2119 electric throttle control actuator

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition
P2119 ETC ACTR-B1 (Throttle actuator control throttle body range/performance) A Electric throttle control actuator does not function properly due to the return spring malfunction.
B Throttle valve opening angle in fail-safe mode is not in specified range
C ECM detect the throttle valve is stuck open.

POSSIBLE CAUSE

Electric throttle control actuator

FAIL-SAFE

Traveling control mode (Engine output control)

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1.  Turn ignition switch OFF and wait at least 10 seconds.
  2.  Turn ignition switch ON.
  3.  Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A AND B

  1.  Turn ignition switch ON and wait at least 1 second.
  2.  Set selector lever to D position and wait at least 3 seconds.
  3.  Set selector lever to P position.
  4.  Turn ignition switch OFF and wait at least 10 seconds.
  5.  Turn ignition switch ON and wait at least 1 second.
  6.  Set selector lever to D position and wait at least 3 seconds.
  7.  Set selector lever to P position.
  8.  Turn ignition switch OFF, wait at least 10 seconds and then turn ON.
  9.  Check DTC.

Is DTC detected? YES >> Proceed to EC-438, "Diagnosis Procedure".

NO >> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION C

  1.  Turn ignition switch ON and wait at least 1 second.
  2.  Set selector lever to D position and wait at least 3 seconds.
  3.  Set selector lever to P position.
  4.  Start engine and let it idle for 3 seconds.
  5.  Check DTC.

Is DTC detected? YES >> Proceed to EC-438, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY

  1.  Remove the intake air duct. Refer to EM-24, "Exploded View".
  2. Check if foreign matter is caught between the throttle valve and the housing.

Is the inspection result normal? YES >> Replace electric throttle control actuator. Refer to EM-26, "Removal and Installation".

NO >> Remove the foreign matter and clean the electric throttle control actuator inside, then perform throttle valve closed position learning. Refer to EC-140, "Work Procedure".

P2118 throttle control motor
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P2118 ETC MOT-B1 (Throttle actuator control motor ...

P2122, P2123 APP sensor
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P2122 APP SEN 1/CIRC (Throttle/pedal position sens ...

Other materials:

Removal and installation
NATS ANTENNA AMP. Removal and Installation REMOVAL  Remove the steering column covers. Refer to IP-17, "Removal and Installation".  Disconnect the harness connector from the NATS antenna amp.  Release pawls and remove NATS antenna amp. (1) from the ignition sw ...

Harness
Harness Layout HOW TO READ HARNESS LAYOUT The following Harness Layouts use a map style grid to help locate connectors on the drawings:  Main Harness and Main Sub Harness  Engine Room Harness  Engine Room Harness (Passenger Compartment)  Front End Module Harness &n ...

Vehicle loading information
WARNING  It is extremely dangerous to ride in a cargo area inside a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.  Do not allow people to ride in any area of your vehicle that is not equipped ...

В© 2014-2026 Copyright t32.nirogue.com