Nissan Rogue Service Manual: P0507 ISC system

Nissan Rogue Service Manual / Engine / Engine Control System / DTC/Circuit diagnosis / P0507 ISC system

Description

The ECM controls the engine idle speed to a specified level through the fine adjustment of the air, which is let into the intake manifold, by operating the electric throttle control actuator. The operating of the throttle valve is varied to allow for optimum control of the engine idling speed. The crankshaft position sensor (POS) detects the actual engine speed and sends a signal to the ECM.

The ECM controls the electric throttle control actuator so that the engine speed coincides with the target value memorized in the ECM. The target engine speed is the lowest speed at which the engine can operate steadily.

The optimum value stored in the ECM is determined by taking into consideration various engine conditions, such as during warming up, deceleration, and engine load (air conditioner, power steering and cooling fan operation, etc.).

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen terms (Trouble diagnosis content)	DTC detecting condition
P0507	ISC SYSTEM (Idle air control system RPM higher than expected)	The idle speed is more than the target idle speed by 200 rpm or more.

POSSIBLE CAUSE

Electric throttle control actuator
Intake air leak
PCV system

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

1.CHECK DTC PRIORITY

If DTC P0507 is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".

NO >> GO TO 2.

2.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.

If the target idle speed is out of the specified value, perform EC-141, "Work Procedure", before conducting DTC Confirmation Procedure.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
Always perform the test at a temperature above −10°C (14°F).

>> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE

Start engine and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Start engine and run it for at least 1 minute at idle speed.
Check 1st trip DTC.

Is 1st trip DTC detected?

YES >> Proceed to EC-355, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK DTC PRIORITY

If DTC P0507 is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".

NO >> GO TO 2.

2.CHECK PCV HOSE CONNECTION

Confirm that PCV hose is connected correctly.

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace error-detected parts.

3.CHECK INTAKE AIR LEAK

Start engine and let it idle.
Listen for an intake air leak after the mass air flow sensor.

Is intake air leak detected? YES >> Discover air leak location and repair.

NO >> Replace ECM. Refer to EC-499, "Removal and Installation".

P0506 ISC system

Description The ECM controls the engine idle speed to a specified level through the fine adjustment of the air, which is let into the intake manifold, by operating the electric throttle control ac ...

P050A, P050B, P050E cold start control

Description ECM controls ignition timing and engine idle speed when engine is started with pre-warming up condition. This control promotes the activation of three way catalyst by heating the c ...

Other materials:

Brake booster
Inspection Operation Depress the brake pedal several times at five second intervals with the engine stopped. Start the engine with the brake pedal fully depressed. Check that the clearance between brake pedal and dash lower panel decreases. NOTE: A slight impact with a small click may be fe ...

NISSAN Intelligent Key® Operation
NISSAN Intelligent Key® Operation You can lock or unlock the doors without taking the Intelligent Key out of your pocket or bag. When you carry the Intelligent Key with you, you can lock or unlock all doors by pushing the door handle request switch within the range of operation. Loc ...

C1765, C1766, C1767, C1768 tire pressure sensor
DTC Description DTC DETECTION LOGIC DTC Display Item Malfunction Detected Condition Possible Cause C1765 WHEEL TOP DATA FL (Wheel top data front left) Malfunction in the wheel top data from the front LH wheel speed sensor. Wheel speed sensor C1766 ...