Nissan Rogue Owners Manual: Troubleshooting guide

Nissan Rogue Owners Manual / Pre-driving checks and adjustments / NISSAN Intelligent Key® (if so equipped) / Troubleshooting guide

Verify the location of all Intelligent Keys that are programmed for the vehicle. If another Intelligent Key is in range or inside the vehicle, the vehicle system may respond differently than expected.

Symptom		Possible Cause	Remedy
When stopping the engine	The Shift to Park warning appears on the display and the inside warning chime sounds continuously.	The shift lever is not in the P (Park) position.	Move the shift lever to the P (Park) position.
When shifting the shift lever to the P (Park) position	The Push ignition to OFF warning appears in the display.	The ignition switch is in the ACC or ON position.	Place the ignition switch in the OFF position.
When opening the driver’s door to get out of the vehicle	The Door Open warning appears on the display and the inside warning chime sounds continuously.	The ignition switch is in the ACC or ON position.	Place the ignition switch in the OFF position.
When closing the door after getting out of the vehicle	The No Key Detected warning appears on the display, the outside chime sounds three times and the inside warning chime sounds for approximately three seconds.	The ignition switch is in the ACC or ON position.	Place the ignition switch in the OFF position.
When closing the door after getting out of the vehicle	The Shift to Park warning appears on the display and the outside chime sounds continuously.	The ignition switch is in the ACC position and the shift lever is not in the P (Park) position.	Move the shift lever to the P (Park) position and place the ignition switch in the OFF position
When closing the door with the inside lock knob turned to LOCK	The outside chime sounds for approximately three seconds and all the doors unlock.	The Intelligent Key is inside the vehicle.	Carry the Intelligent Key with you.
When pushing the door handle request switch or the LOCK button on the Intelligent Key to lock the door	The outside chime sounds for approximately two seconds.	The Intelligent Key is inside the vehicle.	Carry the Intelligent Key with you.
When pushing the ignition switch to start the engine	The Intelligent Key battery indicator appears on the display.	The battery charge is low.	Replace the battery with a new one. (For additional information, refer to “Battery replacement” in the “Maintenance and do-ityourself” section.)
When pushing the ignition switch to start the engine	The No Key Detected warning appears on the display, the outside chime sounds three times and the inside warning chime sounds for approximately three seconds.	The Intelligent Key is not in the vehicle.	Carry the Intelligent Key with you.
When pushing the ignition switch	The Intelligent Key system warning light in the meter illuminates in yellow.	It warns of a malfunction with the Intelligent Key system.	Contact a NISSAN dealer.

How to use the remote keyless entry function

The remote keyless entry function can operate all door locks using the remote keyless function of the Intelligent Key. The remote keyless function can operate at a distance of 33 ft (10 m) away fr ...

Hood

Hood Pull the hood lock release handle 1 located below the instrument panel until the hood springs up slightly. Locate the lever 2 in between the hood and grille and push the lever ...

Other materials:

Using the system
The NISSAN Voice Recognition system allows hands-free operation of the Bluetooth® Hands- Free Phone System. If the vehicle is in motion, some commands may not be available so full attention may be given to vehicle operation. Initialization When the ignition switch is placed in the ON posi ...

VDC off switch
Removal and Installation REMOVAL Remove the instrument lower panel LH. Refer to IP-14, "INSTRUMENT PANEL ASSEMBLY : Removal and Installation". Release pawls using suitable tool and remove the VDC OFF switch (2) from the upper switch carrier (1). : Pawl INST ...

Spark plug
Exploded view Ignition coil Spark plug Rocker cover Removal and installation REMOVAL Remove air duct assembly. Remove ignition coil. Refer to EM-36, "Exploded View". Remove spark plug using Tool. Tool number : — (J-48891) INSPECT ...