Nissan Rogue Service Manual: Parking brake switch
Component Function Check
1.CHECK PARKING BRAKE SWITCH OPERATION
Check that brake warning lamp in combination meter turns ON/OFF when parking brake is operated.
Is the inspection result normal? YES >> Inspection End.
NO >> Proceed to BRC-115, "Diagnosis Procedure".
Diagnosis Procedure
1.CHECK PARKING BRAKE SWITCH CIRCUIT
- Turn the ignition switch OFF.
- Disconnect parking brake switch harness connector.
- Disconnect combination meter harness connector.
- Check the continuity between parking brake switch harness connector and combination meter harness connector.
- Check the continuity between parking brake switch harness connector and ground.
Is the inspection result normal? YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.CHECK PARKING BRAKE SWITCH
Check the parking brake switch. Refer to PB-4, "Inspection and Adjustment".
Is the inspection result normal? YES >> GO TO 3.
NO >> Replace the parking brake switch. Refer to PB-7, "Exploded View".
3.CHECK PARKING BRAKE SWITCH SIGNAL
With CONSULT
- Connect parking brake switch harness connector.
- Connect combination meter harness connector.
- Select “ABS”, “DATA MONITOR” and “PARK BRAKE SW” according to this order. Check the parking brake switch signal.
Is the inspection result normal? YES >> Inspection End.
NO >> GO TO 4.
4.CHECK COMBINATION METER
Check the combination meter. Refer to MWI-21, "CONSULT Function (METER/M&A)".
Is the inspection result normal? YES >> GO TO 5.
NO >> Repair or replace combination meter. Refer to MWI-82, "Removal and Installation".
5.CHECK TERMINAL
- Check the combination meter pin terminals for damage or loose connection with harness connector.
- Check the parking brake switch pin terminals for damage or loose connection with harness connector.
Is the inspection result normal? YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-136, "Removal and Installation".
NO >> Repair or replace error-detected parts.
Component Inspection
1.CHECK PARKING BRAKE SWITCH
- Turn the ignition switch OFF.
- Disconnect parking brake switch harness connector.
- Check the continuity between parking brake switch terminal and ground.
Is the inspection result normal? YES >> Inspection End.
NO >> Replace the parking brake switch. Refer to PB-7, "Exploded View".
Power supply and ground circuit
Diagnosis Procedure
Regarding Wiring Diagram information, refer to PCS-24, "Wiring Diagram".
1. CHECK FUSE AND FUSIBLE LINKS
Check that the following IPDM E/R fuse or fusible links are no ...
VDC off switch
Component Function Check
1.CHECK VDC OFF SWITCH OPERATION
Check that VDC OFF indicator lamp in combination meter turns ON/OFF when VDC
OFF switch is operated.
Is the inspection result normal?
...
Other materials:
Front wiper motor lo circuit
Component Function Check
1.CHECK FRONT WIPER LO OPERATION
CONSULT ACTIVE TEST
Select FR WIPER of BCM (WIPER) active test item.
Check front wiper operation.
LO : Front wiper (LO) operation
OFF : Front wiper OFF
Is the inspection result normal?
YES >> Front wiper motor ...
Driver side door mirror defogger
Description
Heats the heating wire with the power supply from the rear window defogger
relay to prevent the door mirror
from fogging up.
Component Function Check
1. CHECK DOOR MIRROR DEFOGGER LH
Check that heating wire of door mirror defogger LH is heated when turning the
rear window defogg ...
Blind Spot Warning (BSW) System / Lane
Departure Warning (LDW) System (if so equipped)
The Blind Spot Warning (BSW) system helps
alert the driver of other vehicles in adjacent lanes
when changing lanes.
The Lane Departure Warning (LDW) system
helps alert the driver when the vehicle is traveling
close to either the left or the right of a traveling
lane.
The BSW/LDW systems ...
