Nissan Rogue manuals

Nissan Rogue Service Manual: DTC/circuit diagnosis

Nissan Rogue Service Manual / Electrical & power control / Power Control System / IPDM E/R / DTC/circuit diagnosis

U1000 CAN COMM CIRCUIT

Description

Refer to LAN-8, "System Description".

DTC Logic

DTC DETECTION LOGIC

CONSULT Display

DTC Detection Condition

Possible Cause
CAN COMM CIRCUIT [U1000] When IPDM E/R cannot communicate with CAN communication signal continuously for 2 seconds or more. In CAN communication system, any item (or items) of the following listed below is malfunctioning:
  •  Transmission
  •  Receiving (ECM)
  •  Receiving (BCM)
  •  Receiving (Combination meter)

Diagnosis Procedure

1. PERFORM SELF DIAGNOSTIC RESULT

  1.  Turn ignition switch ON and wait for 2 second or more.
  2.  Check “SELF-DIAG RESULTS” of “IPDM E/R”.

Is “CAN COMM CIRCUIT” displayed? YES >> Refer to LAN-17, "Trouble Diagnosis Flow Chart".

NO >> Refer to GI-41, "Intermittent Incident".

B120E IPDM E/R

DTC Logic

DTC DETECTION LOGIC

CONSULT Display

DTC Detection Condition

Possible Cause
USM ECU Not configured [B120E] The IPDM E/R detects 0V for greater than 2 seconds.

ECU internal failure.

 IPDM E/R

DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION

  1.  Turn ignition switch ON.
  2.  Turn ignition switch OFF and wait 1 second or more.
  3.  Turn ignition switch ON.
  4. Perform “Self Diagnostic Result” of “IPDM E/R” using CONSULT.

Is DTC B120E displayed? YES >> Refer to PCS-32, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

1. PERFORM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “IPDM E/R” using CONSULT.

Is display history of DTC B120E CRNT? YES >> Replace IPDM E/R. Refer to PCS-35, "Removal and Installation".

NO >> Refer to GI-41, "Intermittent Incident".

B120E IPDM E/R

DTC Logic

DTC DETECTION LOGIC

CONSULT Display

DTC Detection Condition

Possible Cause
USM ECU Not configured [B120E] The IPDM E/R detects 0V for greater than 2 seconds.

ECU internal failure.

 IPDM E/R

DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION

  1.  Turn ignition switch ON.
  2.  Turn ignition switch OFF and wait 1 second or more.
  3.  Turn ignition switch ON.
  4.  Perform “Self Diagnostic Result” of “IPDM E/R” using CONSULT.

Is DTC B120E displayed? YES >> Refer to PCS-32, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

1. PERFORM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “IPDM E/R” using CONSULT.

Is display history of DTC B120E CRNT? YES >> Replace IPDM E/R. Refer to PCS-35, "Removal and Installation".

NO >> Refer to GI-41, "Intermittent Incident".

B20DD IGNITION RELAY ON CIRCUIT

DTC Logic

DTC DETECTION LOGIC

CONSULT Display

DTC Detection Condition

Possible Cause
IGN RELAY ON [B20DD] The ignition relay ON is detected for 1 second at ignition switch OFF (CPU monitors the status at the contact and excitation coil circuits of the ignition relay inside it IPDM E/R

DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION

  1.  Turn ignition switch ON.
  2.  Turn ignition switch OFF and wait 1 second or more.
  3.  Turn ignition switch ON.
  4.  Perform “Self Diagnostic Result” of “IPDM E/R” using CONSULT.

Is DTC B20DD displayed? YES >> Refer to PCS-32, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

1. PERFORM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “IPDM E/R” using CONSULT.

Is display history of DTC B20DD CRNT? YES >> Replace IPDM E/R. Refer to PCS-35, "Removal and Installation".

NO >> Refer to GI-41, "Intermittent Incident".

B20DE IGNITION RELAY OFF CIRCUIT

DTC Logic

DTC DETECTION LOGIC

CONSULT Display

DTC Detection Condition

Possible Cause
IGN RELAY OFF [B20DE] The ignition relay OFF is detected for 1 second at ignition switch ON (CPU monitors the status at the contact and excitation coil circuits of the ignition relay inside it). IPDM E/R

DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION

  1.  Turn ignition switch ON.
  2.  Turn ignition switch OFF and wait 1 second or more.
  3.  Turn ignition switch ON.
  4. Perform “Self Diagnostic Result” of “IPDM E/R” using CONSULT.

Is DTC B20DE displayed? YES >> Refer to PCS-33, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

1. PERFORM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “IPDM E/R” using CONSULT.

Is display history of DTC B20DE CRNT? YES >> Replace IPDM E/R. Refer to PCS-35, "Removal and Installation".

NO >> Refer to GI-41, "Intermittent Incident".

POWER SUPPLY AND GROUND CIRCUIT

Diagnosis Procedure

Regarding Wiring Diagram information, refer to PCS-24, "Wiring Diagram".

1. CHECK FUSE AND FUSIBLE LINKS

Check that the following IPDM E/R fuse or fusible links are not blown.

Check fuse and fusible links

Is the fuse blown? YES >> Replace the blown fuse or fusible link after repairing the affected circuit.

NO >> GO TO 2.

2. CHECK BATTERY POWER SUPPLY CIRCUIT

  1.  Disconnect IPDM E/R connector E118.
  2.  Check voltage between IPDM E/R connector E118 and ground.

Check battery power supply circuit

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace harness or connectors.

3. CHECK GROUND CIRCUIT

  1.  Disconnect IPDM E/R connectors E119, E120 and E121.
  2.  Check continuity between IPDM E/R connectors and ground.

Check ground circuit

Is the inspection result normal? YES >> Inspection End.

NO >> Repair or replace harness or connectors.

Wiring diagram
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) Wiring Diagram ...

Removal and installation
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) Exploded View IPDM E/R cover IPDM E/R IPDM E/R case IPDM E/R harness cover A IPDM E/R harness cover B Front Remo ...

Other materials:

Preparation
Special Service Tool Tool number (TechMate No.) Tool name Description — (J-46534) Trim Tool Set Removing trim components Commercial Service Tool (TechMate No.) Tool name Description ( — ) Power tool Loo ...

Unit disassembly and assembly
CENTER CONSOLE ASSEMBLY Exploded View Center console cup holder (without heated seats)  Coin tray insert  Center console cup holder (with heated seats)  Front heated seat switch (RH) Front heated seat switch (LH) Shift selector finisher  Shift selector ...

Rocker cover
Oil filler cap  Rocker cover  Rocker cover gasket  Refer to INSTALLATION Engine front Removal and Installation REMOVAL  Remove intake manifold. Refer to EM-26, "Removal and Installation".  Remove wheel and tire (RH) using a power to ...

© 2014-2026 Copyright t32.nirogue.com