Nissan Rogue Owners Manual: Heater operation
Heating
This mode is used to direct heated air to the foot outlets. Some air also flows from the defrost outlets and the side vent outlets.
- Press the
button to
change to fresh
air intake mode. The 
indicator
light
will turn off for normal heating. - Press the
air flow
control button. - Turn the fan control dial to the desired position
- Turn the temperature control dial to the desired position between the middle and the hot position.
Ventilation
This mode directs outside air to the side and center vents.
- Press the
button to
change to fresh
air intake mode. The 
indicator
light
will turn off. - Press the
air flow
control button. - Turn the fan control dial to the desired position.
- Turn the temperature control dial to the desired position.
Defrosting or defogging
This mode directs the air to the defrost outlets to defrost/defog the windows.
- Press the defrost/defog button
. - Turn the fan control dial to the desired position.
- Turn the temperature control dial to the desired position between the middle and the hot position.
- To quickly remove ice or fog from the windows, turn the fan control dial to the highest setting and the temperature control to the full HOT position.
- When the
position is
selected, the air
conditioner automatically turns on if the outside
temperature is more than 36°F (2°C).This dehumidifies the air which helps defog the windshield. The
indicator
automatically
turns off, allowing outside air to be
drawn into the passenger compartment to
further improve the defogging performance.The recirculation mode cannot be activated in the
position.
Bi-level heating
The bi-level mode directs warmed air to the side and center vents and to the front and rear floor outlets.
- Press the
button to
change to fresh
air intake mode. The 
will turn off. - Press the
air flow
control button. - Turn the fan control dial to the desired position.
- Turn the temperature control dial to the desired position.
Heating and defogging
This mode heats the interior and defogs the windshield.
- Press the
air flow
control button. - Turn the fan control dial to the desired position.
- Turn the temperature control dial to the desired position between the middle and the hot position.
- When the
position is
selected, the air
conditioner automatically turns on if the outside
temperature is more than 36°F (2°C).This dehumidifies the air which helps defog the windshield. The
indicator
automatically
turns off, allowing outside air to be
drawn into the passenger compartment to
further improve the defogging performance.
Operating tips
Clear snow and ice from the wiper blades and air inlet in front of the windshield. This improves heater operation.
Controls
Fan control dial
The fan control dial turns the fan on and off, and
controls fan speed.
Air flow control buttons
The air flow control buttons allow you to select
the air flow outlets.
MAX A/C ...
Air conditioner operation
Start the engine, turn the fan control dial to the
desired position, and press the
button to
activate the air conditioner. When the air conditioner
is on, cooling and dehumidifying functions
ar ...
Other materials:
P0711 transmission fluid temperature sensor A
DTC Description
DTC DETECTION LOGIC
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P0711
FLUID TEMP SENSOR A
(Transmission Fluid Temperature Sensor A
Circuit Range/Performance)
When any of 1 or 2 is satisfied:
Under the followi ...
U1010 control unit (CAN)
DTC Logic
DTC DETECTION LOGIC
DTC
Display Item
Malfunction Detected Condition
Possible cause
U1010
CONTROL UNIT (CAN)
BCM detected internal CAN communication circuit malfunction.
BCM
Diagnosis Procedure
1.REPLACE BCM
When DTC “U1010” is detected, repla ...
System
FRONT WIPER AND WASHER SYSTEM
FRONT WIPER AND WASHER SYSTEM : System Diagram
FRONT WIPER AND WASHER SYSTEM : System Description
OUTLINE
FRONT WIPER CONTROL (BASIC)
BCM detects the combination switch position by the combination
switch reading function.
BCM transmits the f ...
