Nissan Rogue Service Manual: Brake warning lamp
Component Function Check
1.CHECK BRAKE WARNING LAMP FUNCTION
Check that brake warning lamp in combination meter turns ON for 1 second after ignition switch is turned ON.
CAUTION: Never start the engine. Is the inspection result normal? YES >> GO TO 2.
NO >> Proceed to BRC-120, "Diagnosis Procedure".
2.CHECK BRAKE WARNING LAMP FUNCTION
Check that brake warning lamp turns ON/OFF when parking brake is operated.
NOTE: Brake warning lamp turns ON when parking brake is operated (when parking brake switch is ON). Is the inspection result normal? YES >> GO TO 3.
NO >> Check the parking brake switch system. Refer to BRC-115, "Diagnosis Procedure".
3.CHECK BRAKE WARNING LAMP FUNCTION
Check that brake warning lamp in combination meter turns ON/OFF when brake fluid level switch is operated while brake fluid level in reservoir tank is with the specified level.
NOTE: Brake warning lamp turns ON when brake fluid is less than the specified level (when brake fluid level switch is ON). Is the inspection result normal? YES >> Inspection End.
NO >> Check the brake fluid level switch system. Refer to BR-27, "Exploded View".
Diagnosis Procedure
1.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.
Refer to BRC-120, "Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.PERFORM THE SELF-DIAGNOSIS
With CONSULT
- Turn the ignition switch OFF → ON.
CAUTION:
- Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
- Start the engine.
- Repeat step 1 two or more times.
- Perform self-diagnosis for “ABS”.
Is any DTC detected? YES >> Check the DTC. Refer to BRC-55, "DTC Index".
NO >> GO TO 3.
3.CHECK BRAKE WARNING LAMP SIGNAL
With CONSULT
- Select “ABS”, “DATA MONITOR” and “EBD WARN LAMP” according to this order.
- Turn the ignition switch OFF.
- Check that data monitor displays “On” for 1 second after ignition switch is turned ON and then changes to “Off”.
CAUTION: Never start the engine. Is the inspection result normal? YES >> Replace the combination meter. Refer to MWI-82, "Removal and Installation".
NO >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-136, "Removal and Installation".
ABC warning lamp
Component Function Check
1.CHECK ABS WARNING LAMP FUNCTION
Check that ABS warning lamp in combination meter turns ON for 1 second after
ignition switch is turned ON.
CAUTION:
Never start the eng ...
VDC warning lamp
Component Function Check
1.CHECK VDC WARNING LAMP FUNCTION
Check that VDC warning lamp in combination meter turns ON for 1 second after
ignition switch is turned ON.
CAUTION:
Never start the e ...
Other materials:
Both doors mirror defogger don’t operate but rear window defogger operates
Diagnosis Procedure
Regarding Wiring Diagram information, refer to DEF-12, "Wiring Diagram".
1. CHECK DOOR MIRROR DEFOGGER FUSE
Check if the following fuse in fuse block (J/B) is blown.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace the blown fuse af ...
Reporting safety defects
For USA
If you believe that your vehicle has a defect
which could cause a crash or could
cause injury or death, you should immediately
inform the National Highway Traffic
Safety Administration (NHTSA) in addition
to notifying NISSAN.
If NHTSA receives similar complaints, it
may open an inv ...
VIN registration
Description
VIN Registration is an operation to registering VIN in ECM. It must be
performed each time ECM is replaced.
NOTE:
Accurate VIN which is registered in ECM may be required for Inspection &
Maintenance (I/M).
Work Procedure
1.CHECK VIN
Check the VIN of the vehicle and note it. ...
