Nissan Rogue Service Manual: B1431 seat belt pre-tensioner
DTC Logic
DTC DETECTION LOGIC
|
CONSULT name |
DTC |
DTC detecting condition |
Repair order |
| FRONT PRE-TEN RH CIRCUIT [OPEN] | B1431 | RH seat belt pre-tensioner circuit is open. | Refer to SRC-61, "Diagnosis Procedure" |
| FRONT PRE-TEN RH CIRCUIT [VB-SHORT] | RH seat belt pre-tensioner circuit is shorted to a power supply circuit. | ||
| FRONT PRE-TEN RH CIRCUIT [GND-SHORT] | RH seat belt pre-tensioner circuit is shorted to ground. | ||
| FRONT PRE-TEN RH CIRCUIT [SHORT] | RH seat belt pre-tensioner circuits are shorted to each other. |
DTC CONFIRMATION PROCEDURE (With CONSULT)
1.CHECK SELF-DIAG RESULT
- Turn ignition switch ON.
- Check for DTC using CONSULT.
Is the DTC detected? YES (Current DTC)>>Refer to SRC-61, "Diagnosis Procedure".
YES (Past DTC)>>GO TO 2.
NO >> Inspection End.
2.ERASE SELF-DIAG RESULT
Erase the DTC using CONSULT.
Can the DTC be erased? YES >> Inspection End.
NO >> Refer to SRC-61, "Diagnosis Procedure".
DTC CONFIRMATION PROCEDURE (Without CONSULT)
1.CHECK SELF-DIAG RESULT
- Turn ignition switch ON.
- Check the air bag warning lamp status. Refer to SRC-16, "On Board Diagnosis Function".
NOTE: SRS will not enter diagnosis mode if no malfunction is detected in user mode.
Is the DTC detected? YES >> Refer to SRC-61, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis Procedure
1.HARNESS CONNECTOR
Check the harness connector for the following:
- Visible damage to connector or terminal
- Loose terminal
- Poor connection
Is the inspection result normal? YES >> GO TO 2.
NO >> Perform one of the following repairs:
- Visible damage: Replace the harness.
- Loose terminal: Secure the terminal.
- Poor connection: Secure the connection.
2.CONFIRM DTC
- Reconnect all harness connectors.
- Turn ignition switch ON.
- Check for DTC using CONSULT.
Is DTC still current? YES >> GO TO 3.
NO >> Refer to GI-41, "Intermittent Incident".
3.WIRING HARNESS
Check the wiring harness for visible damage.
NOTE: The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors). Is the inspection result normal? YES >> GO TO 4.
NO >> Replace the harness.
4.CONFIRM DTC
- Reconnect all harness connectors.
- Turn ignition switch ON.
- Check for DTC using CONSULT.
Is DTC still current? YES >> GO TO 5.
NO >> Refer to GI-41, "Intermittent Incident".
5.AIR BAG DIAGNOSIS SENSOR UNIT
- Replace the air bag diagnosis sensor unit. Refer to SR-26, "Removal and Installation".
- Turn ignition switch ON.
- Check for DTC using CONSULT.
Is DTC still current? YES >> GO TO 6.
NO >> Clear DTC. Inspection End.
6.SEAT BELT PRE-TENSIONER RH
- Replace the seat belt pre-tensioner RH. Refer to SR-28, "Removal and Installation".
- Turn ignition switch ON.
- Check for DTC using CONSULT.
Is DTC still current? YES >> GO TO 7.
NO >> Clear DTC. Inspection End.
7.RELATED HARNESS
Replace the related harness.
>> END
B1430 seat belt pre-tensioner
DTC Logic
DTC DETECTION LOGIC
CONSULT name
DTC
DTC detecting condition
Repair order
FRONT PRE-TEN LH CIRCUIT
[OPEN]
B1430
Front LH seat belt pre-ten ...
B1428 seat belt buckle switch IH
Description
DTC B1428 SEAT BELT BUCKLE SWITCH LH
The air bag diagnosis sensor unit monitors the seat belt buckle switch LH
status. If the control unit detects an
open or short condition in the ci ...
Other materials:
B14XX air bag diagnosis sensor unit
Description
DTC B1XXX AIR BAG DIAGNOSIS SENSOR UNIT
The air bag diagnosis sensor unit will run self diagnostics when the ignition
switch is turned ON. It has the
potential to set many diagnostic trouble codes which will conform to the B1XXX
format, but will not match any
other SRS diagnostic ...
Front wiper and washer system
Wiring Diagram
...
How to use this manual
How to use this manual
Description
This volume explains “Removal, Disassembly, Installation, Inspection and
Adjustment” and “Trouble Diagnoses”.
Terms
The captions WARNING and CAUTION warn you of steps that must be followed
to prevent personal injury
and/or damage to some par ...
