Nissan Rogue manuals

Nissan Rogue Service Manual: Front washer nozzle and tube

Nissan Rogue Service Manual / Driver controls / Wiper & Washer / Removal and installation / Front washer nozzle and tube

Exploded View

Exploded View

  1. Cowl top cover
  2. Front washer tube
  3. Front washer nozzle (LH)
  4.  Front washer nozzle (RH)

Pawl
Clip

Exploded View

Exploded View

  1. Cowl top cover
  2. Front washer tube

Clip

Removal and Installation - Front Washer Nozzle

REMOVAL

  1.  Remove front wiper arms (LH/RH). Refer to WW-63, "Removal and Installation".
  2. Release pawls using suitable tool (A) and remove cowl top side trim cover (1) (LH/RH).

    : Pawl

Removal

  1. Disconnect front washer tube connector.

Removal

  1. Release pawls and remove front washer nozzle (LH/RH).

INSTALLATION

Installation is in the reverse order of removal.

CAUTION: Adjust the nozzle spray pattern. Refer to WW-61, "Inspection and Adjustment".

Removal and Installation - Front Washer Tube

REMOVAL

  1.  Disconnect front washer tube connector.

Removal

  1. Remove engine side cover. Refer to EXT-28, "FENDER PROTECTOR : Exploded View".
  2.  Remove engine undercover. Refer to EXT-37, "ENGINE UNDER COVER : Removal and Installation".
  3.  Partially remove fender protector. Refer to EXT-28, "FENDER PROTECTOR : Exploded View".
  4.  Unclip front washer hose and remove.

INSTALLATION

Installation is in the reverse order of removal.

Inspection and Adjustment

WASHER TUBE INSPECTION

Check that air can pass through the check valve splitter by blowing into the check valve splitter and that air cannot flow in the opposite direction.

O: Air can flow
X: Air cannot flow

Washer tube inspection

ADJUSTMENT

If operating properly, spray positions should match the positions shown. If spray positions do not match, confirm the rear washer nozzle is properly seated and working properly. If the spray positions still do not match as shown, then replace the front washer nozzle. Refer to WW-60, "Removal and Installation - Front Washer Nozzle"

Adjustment

  1. Windshield glass
  2. Black printed area line
  3. Front washer nozzle (LH/RH)
  4.  Center line
  5.  409 mm (16.10 in)
  6.  103 mm (4.06 in)
  7.  497 mm (19.57 in)
  8.  398 mm (15.67 in)
  9.  100 mm (3.94 in)
  10.  356 mm (14.02 in)
  11.  127 mm (5.00 in)
  12.  93 mm (3.66 in)
  13. 80 mm (3.15 in)
  14.  133 mm (5.24 in)
  15. 354 mm (13.94 in)
  16.  90 mm (3.54 in)
  17. 380 mm (14.96 in)
  18. 496 mm (19.53 in)
  19.  103 mm (4.06 in)
  20. 409 mm (16.10 in)
Washer fluid level switch
Removal and Installation The washer fluid level switch is serviced as a part of the washer tank. Refer to WW-56, "Removal and Installation". ...

Front wiper arm
Exploded View Front wiper blade (RH) Front wiper arm (RH)  Front wiper arm cover  Front wiper drive assembly Front wiper arm (LH)  Front wiper blade (LH) Removal ...

Other materials:

System description
COMPONENT PARTS Component Parts Location Center of back door View with glove box removed No Component Function 1 Rod antenna Refer to AV-232, "Rod Antenna, Antenna Amp., Satellite Antenna and Antenna Feeder". 2 Antenna ...

DTC/circuit diagnosis
U1000 CAN COMM CIRCUIT Description Refer to LAN-8, "System Description". DTC Logic DTC DETECTION LOGIC NOTE: U1000 can be set if a module harness was disconnected and reconnected, perhaps during a repair. Confirm that there are actual CAN diagnostic symptoms and a present DTC by p ...

Connector Symbols
Most of connector symbols in wiring diagrams are shown from the terminal side.  Connector symbols shown from the terminal side are enclosed by a single line and followed by the direction mark.  Connector symbols shown from the harness side are enclosed by a double line and foll ...

В© 2014-2026 Copyright t32.nirogue.com