Nissan Rogue manuals

Nissan Rogue Service Manual: Brake booster

Nissan Rogue Service Manual / Brakes / Brake System / Removal and installation / Brake booster

Exploded View

Exploded View

  1. Spacer
  2. Gasket
  3. Brake booster
  4.  Check valve
  5. Reservoir tank
  6. Brake fluid level sensor
  7.  Brake booster pressure sensor

Removal and installation

REMOVAL

  1.  Remove the cowl top. Refer to EXT-25, "Removal and Installation".
  2.  Remove the instrument lower panel LH. Refer to IP-22, "Removal and Installation".
  3.  Remove the knee protector. Refer to IP-14, "Exploded View".
  4.  Remove the snap pin (1) and clevis pin (2) from the brake pedal.

Removal

  1. Disconnect vacuum hose from brake booster. Refer to BR-32, "Exploded View".
  2. Remove master cylinder assembly. Refer to BR-27, "Removal and Installation".
  3.  Disconnect the harness connector from the brake booster pressure sensor.
  4.  Remove the brake booster pressure sensor.
  5.  Remove the nuts on the brake booster and brake pedal.

    CAUTION: Secure the brake booster to avoid damage to components.

  6.  Remove the brake booster.

    CAUTION: Do not deform or bend the brake pipes.

INSTALLATION

  1. Install a new gasket between the brake booster and dash panel.

    CAUTION: Do not reuse the gasket.

  2.  Install the brake booster to the dash panel from the engine room side.

    CAUTION: Do not damage brake booster stud bolt threads during installation.

  3.  Install the nuts to the brake booster and brake pedal. Refer to BR-30, "Exploded View".
  4.  Install the brake booster pressure sensor.
  5.  Connect the harness connector to the brake booster pressure sensor.
  6.  Install master cylinder assembly. Refer to BR-27, "Removal and Installation".
  7.  Connect vacuum hose to brake booster. Refer toBR-32, "Exploded View".
  8.  Install the clevis pin and snap pin to the brake pedal.
  9.  Adjust the brake pedal. Refer to BR-15, "Adjustment".
  10.  Install the knee protector. Refer to IP-14, "Exploded View".
  11.  Install instrument lower panel LH. Refer to IP-22, "Removal and Installation".
  12.  Bleed the brake system. Refer to BR-16, "Bleeding Brake System".
  13.  Inspect the brake booster. Refer to BR-10, "Inspection".
Brake master cylinder
Exploded View Reservoir cap Oil strainer Reservoir tank  Brake fluid level sensor Cylinder body Pin O-ring Grommet : Apply PBC (Poly Butyl Cuprysil) grease or sil ...

Vacuum lines
Exploded View Clamp Vacuum hose Vacuum tube  Clip Vacuum hose  To intake manifold To brake booster Paint mark Stamp indicating engine direction Removal an ...

Other materials:

Service data and specifications (SDS)
General Specification GENERAL SPECIFICATIONS ( ): Valve timing control “ON” Drive belt Spark Plug Intake Manifold Exhaust Manifold Camshaft *1: Cam wear limit *2: Total indicator reading VALVE LIFTER VALVE CLEARANCE *: Approximately 80°C (176°F) AVAIL ...

Preparation
Special Service Tool The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name Description KV991J0070 (J-45695-A) Coolant refill tool Refilling engine cooling system Commercial Service Too ...

Satellite radio reception (if so equipped)
When the satellite radio is used for the first time or the battery has been replaced, the satellite radio may not work properly. This is not a malfunction. Wait more than 10 minutes with satellite radio ON and the vehicle outside of any metal or large building for satellite radio to receive a ...

© 2014-2026 Copyright t32.nirogue.com