Nissan Rogue Service Manual: Additional service when replacing ECM

Nissan Rogue Service Manual / Engine / Engine Control System / Basic inspection / Additional service when replacing ECM

Description

When replacing ECM, the following procedure must be performed. (For details, refer to EC-136, "Work Procedure".)

PROGRAMMING OPERATION

NOTE: After replacing with a blank ECM, programming is required to write ECM information. Be sure to follow the procedure to perform the programming.

Work Procedure

1.SAVE ECM DATA

With CONSULT

Turn ignition switch OFF.
Reconnect all harness connectors disconnected.
Turn ignition switch ON.
Select “SAVING DATA FOR REPLC CPU” in “WORK SUPPORT” mode of “ENGINE” using CONSULT.
Follow the instruction of CONSULT display.

NOTE:

Necessary data in ECM is copied and saved to CONSULT.
Go to Step 2 regardless of with or without success in saving data.

>> GO TO 2.

2.CHECK ECM PART NUMBER

Check ECM part number to see whether it is blank ECM or not.

NOTE:

Part number of blank ECM is 23703 - ЧЧЧЧЧ.
Check part number when ordering ECM or the one included in the label on the container box.

Is the ECM a blank ECM? YES >> GO TO 3.

NO >> GO TO 5.

3.SAVE ECM PART NUMBER

Read out the part number from the old ECM and save the number, following the programming instructions.

Refer to CONSULT Operation Manual.

NOTE:

The ECM part number is saved in CONSULT.
Even when ECM part number is not saved in CONSULT, go to 4.

>> GO TO 4.

4.PERFORM ECM PROGRAMMING

After replacing ECM, perform the ECM programming. Refer to CONSULT Operation Manual.

NOTE:

Refer to EC-499, "Removal and Installation" for replacement of ECM.
During programming, maintain the following conditions:

Ignition switch: ON
Electric load: OFF
Brake pedal: Not depressed
Battery voltage: 12 – 13.5 V (Be sure to check the value of battery voltage by selecting “BATTERY VOLT” in “Data monitor” of CONSULT.)

>> GO TO 6.

5.REPLACE ECM

Replace ECM. Refer to EC-499, "Removal and Installation".

>> GO TO 6.

6.PERFORM INITIALIZATION OF IVIS (NATS) SYSTEM AND REGISTRATION OF ALL IVIS (NATS) IGNITION KEY IDS

Refer to SEC-62, "Work Flow" (with intelligent key system) or SEC-150, "Work Flow" (without intelligent key system).

>> GO TO 7.

7.CHECK ECM DATA STATUS

Check if the data is successfully copied from the ECM at Step 1 (before replacement) and saved in CONSULT.

Is the data saved successfully? YES >> GO TO 8.

NO >> GO TO 9.

8.WRITE ECM DATA

With CONSULT

Select “WRITING DATA FOR REPLC CPU” in “WORK SUPPORT” mode of “ENGINE” using CONSULT.
Follow the instruction of CONSULT display.

NOTE: The data saved by “SAVING DATA FOR REPLC CPU” is written to ECM.

>> GO TO 10.

9.PERFORM VIN REGISTRATION

Refer to EC-138, "Work Procedure".

>> GO TO 10.

10.PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING

Perform Accelerator Pedal Released Position Learning. Refer to EC-139, "Work Procedure".

>> GO TO 11.

11.PERFORM THROTTLE VALVE CLOSED POSITION LEARNING

Perform Throttle Valve Closed Position Learning. Refer to EC-140, "Work Procedure".

>> GO TO 12.

12.PERFORM IDLE AIR VOLUME LEARNING

Perform Idle Air Volume Learning. Refer to EC-141, "Work Procedure".

>> END

Basic inspection

Work Procedure 1.INSPECTION START Check service records for any recent repairs that may indicate a related malfunction, or a current need for scheduled maintenance. Open engine ...

VIN registration

Description VIN Registration is an operation to registering VIN in ECM. It must be performed each time ECM is replaced. NOTE: Accurate VIN which is registered in ECM may be required for Inspectio ...

Other materials:

DTC/circuit diagnosis
U1000 CAN COMM CIRCUIT Description CAN (Controller Area Network) is a serial communication system for real time application. It is an on-vehicle multiplex communication system with high data communication speed and excellent error detection ability. Many electronic control units are equipp ...

U0155 lost communication (IPC)
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U0155 LOST COMM (IPC) [Lost Communication With Instrument Panel Cluster (IPC) Control Module] When the ignition switch is ON, TCM is unable to recei ...

Normal operating condition
Description FRONT WIPER PROTECTION FUNCTION IPDM E/R detects front wiper stop position by a front wiper stop position signal. When a front wiper stop position signal is in the conditions listed below, IPDM E/R stops power supply to wiper after repeating a front wiper 10 seconds activation ...