Nissan Rogue manuals

Nissan Rogue Service Manual: Power supply and ground circuit

Nissan Rogue Service Manual / Body exterior, doors, roof & vehicle security / Power Window Control System / DTC/circuit diagnosis / Power supply and ground circuit

BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM)

BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) : Diagnosis Procedure

Regarding Wiring Diagram information, refer to BCS-50, "Wiring Diagram".

1. CHECK FUSE

Check that the following fuse is not blown.

Is the fuse blown? YES >> Replace the blown fuse after repairing the affected circuit.

NO >> GO TO 2.

2. CHECK POWER SUPPLY CIRCUIT

  1.  Disconnect BCM connector M20.
  2.  Check voltage between BCM connector M20 and ground.

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace harness or connectors.

3. CHECK GROUND CIRCUIT

Check continuity between BCM connector M20 and ground.

Is the inspection result normal? YES >> Inspection End.

NO >> Repair or replace harness or connectors.

BCM (BODY CONTROL SYSTEM) (WITHOUT INTELLIGENT KEY SYSTEM)

BCM (BODY CONTROL SYSTEM) (WITHOUT INTELLIGENT KEY SYSTEM) : Diagnosis Procedure

Regarding Wiring Diagram information, refer to BCS-110, "Wiring Diagram".

1. CHECK FUSE

Check that the following fuse is not blown.

Check fuse

Is the fuse blown? YES >> Replace the blown fuse after repairing the affected circuit.

NO >> GO TO 2.

2. CHECK POWER SUPPLY CIRCUIT

  1.  Disconnect BCM connector M20.
  2.  Check voltage between BCM connector M20 and ground.

Check power supply circuit

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace harness or connectors.

3. CHECK GROUND CIRCUIT

Check continuity between BCM connector M20 and ground.

Check ground circuit

Is the inspection result normal? YES >> Inspection End.

NO >> Repair or replace harness or connectors.

POWER WINDOW MAIN SWITCH

POWER WINDOW MAIN SWITCH : Diagnosis Procedure

1.CHECK POWER SUPPLY CIRCUIT 1

  1.  Turn ignition OFF.
  2. Disconnect main power window and door lock/unlock switch connector.
  3. Turn ignition switch ON.
  4. Check voltage between main power window and door lock/unlock switch harness connector and ground.

Check power supply circuit 1

Is the inspection result normal? YES >> GO TO 2.

NO >> GO TO 4.

2.CHECK POWER SUPPLY CIRCUIT 2

1. Check voltage between main power window and door lock/unlock switch harness connector and ground.

Check power supply circuit 2

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair power supply circuit.

3.CHECK GROUND CIRCUIT

  1.  Turn ignition switch OFF.
  2.  Check continuity between main power window and door lock/unlock switch harness connector and ground.

Check ground circuit

Is the inspection result normal? YES >> Inspection End.

NO >> Repair or replace harness.

4.CHECK HARNESS CONTINUITY 1

  1.  Turn ignition switch OFF.
  2.  Disconnect power window relay connector.
  3. Check continuity between power window relay harness connector and main power window and door lock/ unlock switch harness connector.

Check harness continuity 1

  1. Check continuity between power window relay harness connector and ground.

Check harness continuity 1

Is the inspection result normal? YES >> Refer to PWC-48, "Diagnosis Procedure".

NO >> Repair or replace harness.

FRONT POWER WINDOW SWITCH (PASSENGER SIDE)

FRONT POWER WINDOW SWITCH (PASSENGER SIDE) : Diagnosis Procedure

1.CHECK POWER SUPPLY CIRCUIT

  1.  Turn ignition switch OFF.
  2.  Disconnect front power window switch RH connector.
  3.  Turn ignition switch ON.
  4.  Check voltage between front power window switch RH harness connector and ground.

Check power supply circuit

Is the inspection result normal? YES >> Inspection End.

NO >> GO TO 2.

2.CHECK HARNESS CONTINUITY

  1.  Turn ignition switch OFF.
  2.  Disconnect power window relay connector.
  3.  Check continuity between power window relay harness connector and front power window switch RH harness connector.

Check harness continuity

  1. Check continuity between the power window relay harness connector and ground.

Check harness continuity

Is the inspection result normal? YES >> Refer to PWC-48, "Diagnosis Procedure".

NO >> Repair or replace harness.

REAR POWER WINDOW SWITCH

REAR POWER WINDOW SWITCH : Diagnosis Procedure

1.CHECK POWER SUPPLY CIRCUIT

  1.  Turn ignition switch OFF.
  2.  Disconnect rear power window switch connector.
  3.  Turn ignition switch ON.
  4.  Check voltage between rear power window switch harness connector and ground.

Check power supply circuit

Is the inspection result normal? YES >> Inspection End.

NO >> GO TO 2.

2.CHECK HARNESS CONTINUITY

  1.  Turn ignition switch OFF.
  2.  Disconnect power window relay connector.
  3.  Check continuity between power window relay harness connector and rear power window switch harness connector.

Check harness continuity

  1. Check continuity between power window relay harness connector and ground.

Check harness continuity

Is the inspection result normal? YES >> Refer to PWC-48, "Diagnosis Procedure".

NO >> Repair or replace harness.

DTC/circuit diagnosis
...

Front power window switch (passenger side)
Description Front power window motor RH will be operated if front power window switch RH is operated. Component Function Check 1. CHECK FRONT POWER WINDOW SWITCH RH FUNCTION Check front power wi ...

Other materials:

The parking brake release warning continues sounding, or does not sound
Description The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is released.  The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking brake applied. Diagnosis Procedure 1. CHECK P ...

Front wiper drive assembly
Exploded View REMOVAL Cowl top Front wiper drive assembly Removal and Installation REMOVAL  Remove cowl top cover. Refer to EXT-25, "Removal and Installation".  Disconnect harness connector from front wiper motor.  Remove bolts and front wiper driv ...

Preparation
Special Service Tool The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name Description — (J-46534) Trim Tool Set Removing trim components Commercial Service Tools (TechMate No ...

© 2014-2026 Copyright t32.nirogue.com