Nissan Rogue Service Manual: P0746 pressure control solenoid A

Nissan Rogue Service Manual / Transmission & driveline / Transaxle & Transmission / Dtc/circuit diagnosis / P0746 pressure control solenoid A

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms (Trouble diagnosis content)

DTC detection condition

P0746

PC SOLENOID A (Pressure Control Solenoid A Performance/ Stuck Off)

The detecting condition A or detection condition B is detected twice or more (1 second or more later after detection of the first) in the same DC under the following diagnosis conditions:

Diagnosis conditions

Engine speed: More than 600 rpm
Primary pulley speed: More than 450 rpm
Idle is not being detected.
Acceleration/deceleration speed: −0.49 m/s2 (−0.05 G) or more
The primary pulley speed experienced 300 rpm or more and the secondary pulley speed experienced 250 rpm or more at least once.
Secondary pulley speed: More than 150 rpm
TCM power supply voltage: More than 11 V

Detection condition A

Status with the shifting ratio of the primary pulley speed/secondary pulley ratio exceeding 2.981 is 0.2 sec. or more continuously.

Detection condition B

Status with the shifting ratio of the primary pulley speed/secondary pulley ratio exceeding 3.781 is 0.1 sec. or more continuously

NOTE: DC stands for "DRIVING CYCLE" and indicates a series of driving cycle of "Ignition switch OFF → ON → driving → OFF".

POSSIBLE CAUSE

Line pressure solenoid valve
Control valve assembly

FAIL-SAFE

Selector shock is large
Start is slow
Acceleration is slow
Lock-up is not performed

DTC CONFIRMATION PROCEDURE

CAUTION: Be careful of the driving speed.

1.PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

Start the engine.
Drive the vehicle.
Maintain the following conditions for 10 seconds or more.

Selector lever : “D” position
Accelerator pedal position : 0.5/8 or more
Vehicle speed : 40 km/h (25 MPH) or more

Stop the vehicle.
Check the first trip DTC.

Is “P0746”detected? YES >> Go to TM-138, "Diagnosis Procedure".

NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

1.REPLACE TRANSAXLE ASSEMBLY

Replace transaxle assembly. Refer to TM-220, "Removal and Installation".

>> WORK END

P0744 torque converter

DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0744 TORQUE CONVERTER (Torque converter clutch circui ...

P0776 pressure control solenoid B

DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content DTC detection condition P0776 PC SOLENOID B (Pressure Control Solenoid “B” ...

Other materials:

System description
VENTILATION SYSTEM System Description OUTLINE Automatic A/C The ventilation system is controlled by the A/C switch assembly. For details of the automatic air conditioner system, refer to HAC-10, "System Description". Manual A/C The ventilation system is controlled by the front air ...

Diagnosis system (BCM) (without intelligent key system)
COMMON ITEM COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) APPLICATION ITEM CONSULT performs the following functions via CAN communication with BCM. Direct Diagnostic Mode Description Ecu Identification The BCM part number is displayed. Self Diagnostic ...

Exterior front
Front view camera (if so equipped) Engine hood Windshield wiper and washer switch, wiper blades Windshield-washer fluid Windshield Power windows Door locks, NISSAN Intelligent Key® (if so equipped), NISSAN Jackknife key (if so equipped), key ...