Nissan Rogue Service Manual: Excessive operation frequency

Nissan Rogue Service Manual / Brakes / Brake Control System / Symptom diagnosis / Excessive operation frequency

Description

VDC function, TCS function, ABS function, EBD function, Brake limited slip differential (BLSD) function, Brake assist function, hill start assist function or Brake force distribution function operates in excessive operation frequency.

Diagnosis Procedure

1.CHECK BRAKING FORCE

Check brake force using a brake tester.

Is the inspection result normal? YES >> GO TO 2.

NO >> Check brake system.

2.CHECK FRONT AND REAR AXLE

Check that there is no excessive looseness in front and rear axle.

2WD: Refer to FAX-7, "Inspection" (front) or RAX-6, "Inspection" (rear).
AWD: Refer to FAX-38, "Inspection" (front) or RAX-14, "Inspection" (rear).

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace error-detected parts.

3.CHECK WHEEL SENSOR

Check wheel sensor.

Check installation and damage of wheel sensor.
Check connection of wheel sensor harness connector.
Check terminal of wheel sensor harness connector.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair installation or replace wheel sensor.

Front wheel sensor: Refer to BRC-132, "FRONT WHEEL SENSOR : Removal and Installation".
Rear wheel sensor: Refer to BRC-134, "REAR WHEEL SENSOR : Removal and Installation".

4.CHECK SENSOR ROTOR

Check that there is no looseness, damage or foreign material on sensor rotor.

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair installation or replace sensor rotor.

Front sensor rotor: Refer to BRC-135, "FRONT SENSOR ROTOR : Removal and Installation - Front Sensor Rotor".
Rear sensor rotor: Refer to BRC-135, "REAR SENSOR ROTOR : Removal and Installation - Rear Sensor Rotor".

5.CHECK WARNING LAMP TURNS OFF

Check that ABS warning lamp, brake warning lamp and VDC warning lamp turn OFF approx. 1 second after key switch is turned ON and stay in OFF status during driving.

CAUTION: Brake warning lamp turns ON when parking brake is operated (parking brake switch is ON) or brake fluid is less than the specified level (brake fluid level switch is ON). Is the inspection result normal? YES >> Normal NO >> GO TO 6.

6.PERFORM THE SELF-DIAGNOSIS

With CONSULT

Turn the ignition switch OFF → ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
Set the vehicle to READY/Start the engine.

Repeat step 1 two or more times.
Perform self-diagnosis for “ABS”.

Is any DTC detected? YES >> Check the DTC. Refer to BRC-55, "DTC Index".

NO >> Inspection End.

Symptom diagnosis

...

Unexpected brake pedal reaction

Description A malfunction of brake pedal feel (height or others) is detected when brake pedal is depressed. Diagnosis Procedure 1.CHECK FRONT AND REAR AXLE Check that there is no excessive loose ...

Other materials:

Key switch signal circuit (without intelligent key)
Description Transmits a key switch signal to the BCM. Component Function Check 1. CHECK BCM INPUT SIGNAL Select "Data Monitor" for "BCM" and check the "KEY ON SW" monitor value. Is the inspection result normal? YES >> Inspection End. NO >> Refer ...

Lifting point
Special service tool The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here. Tool number (Kent-Moore No.) Tool name Description LM4086-0200 ( - ) Board on attachment LM4519-0000 ( - ) Safety stan ...

Accelerator pedal released position learning
Description Accelerator Pedal Released Position Learning is a function of ECM to learn the fully released position of the accelerator pedal by monitoring the accelerator pedal position sensor output signal. It must be performed each time harness connector of accelerator pedal position sensor ...