Nissan Rogue Service Manual: C1716, C1717, C1718, C1719 transmitter (pressure data)
DTC Logic
NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.
- Activate and display TPMS sensor IDs
- Display tire pressure reported by the TPMS sensor
- Read TPMS DTCs
- Register TPMS sensor IDs
DTC DETECTION LOGIC
|
DTC |
Display Item | Malfunction Detection Condition | Possible Cause |
| C1716 | [PRESSDATA ERR] FL | Malfunction in the tire pressure data from the front LH wheel tire pressure sensor. |
|
| C1717 | [PRESSDATA ERR] FR | Malfunction in the tire pressure data from the front RH wheel tire pressure sensor. | |
| C1718 | [PRESSDATA ERR] RR | Malfunction in the tire pressure data from the rear RH wheel tire pressure sensor. | |
| C1719 | [PRESSDATA ERR] RL | Malfunction in the tire pressure data from the rear LH wheel tire pressure sensor. |
DTC CONFIRMATION PROCEDURE
1.PERFORM SELF DIAGNOSTIC RESULT
With CONSULT
- Check tire pressure for all wheels and adjust to the specified value. Refer to WT-65, "Tire Air Pressure".
- Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- Perform Self Diagnostic Result.
Is DTC C1716, C1717, C1718, or C1719 detected? YES >> Proceed to WT-29, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis Procedure
NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.
- Activate and display TPMS sensor IDs
- Display tire pressure reported by the TPMS sensor
- Read TPMS DTCs
- Register TPMS sensor IDs
1.TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to WT-21, "Work Procedure".
Can the tire pressure sensor ID registration be completed? YES >> GO TO 2.
NO >> Replace applicable tire pressure sensor. Refer to WT-61, "Removal and Installation".
2.CHECK TIRE PRESSURE SIGNAL
With CONSULT
- Adjust tire pressure for all wheels to the specified value. Refer to WT-65, "Tire Air Pressure".
- Select “AIR PRESSURE MONITOR” from “BCM”.
- Check that the air pressures match the specified value.
|
Monitor item |
Displayed value |
| AIR PRESS FL | Approximately equal to specified value. Refer to WT-65, "Tire Air Pressure". |
| AIR PRESS FR | |
| AIR PRESS RR | |
| AIR PRESS RL |
Is the inspection result normal? YES >> Inspection End.
NO >> Replace BCM. Refer to BCS-75, "Removal and Installation" (with Intelligent Key System) or BCS- 135, "Removal and Installation" (without Intelligent Key System).
C1708, C1709, C1710, C1711 transmitter (no data)
DTC Logic
NOTE:
The Signal Tech II Tool [- (J-50190)] can be used to perform the following
functions. Refer to the Signal Tech II
User Guide for additional information.
Activate and dis ...
C1729 vehicle speed signal
DTC Logic
NOTE:
The Signal Tech II Tool [- (J-50190)] can be used to perform the following
functions. Refer to the Signal Tech II
User Guide for additional information.
Activate and dis ...
Other materials:
Supplemental air bag warning labels
SRS Air Bag Warning Labels
SRS Air Bag Warning Labels
The warning labels are located on the surface
of the sun visor.
Warning labels about the supplemental frontimpact
air bag system are placed in the vehicle as
shown in the illustration.
WARNINGExtreme Hazard! Do not us ...
Preparation
Special Service Tool
The actual shape of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name
Description
KV38100500
( — )
Drift
Installing sensor rotor
a: 80 mm (3.15 in) dia.
b: 60 mm (2.36 in) dia.
KV40 ...
The light reminder warning does not sound
Description
Light reminder warning does not sound even though headlamp is illuminated.
Diagnosis Procedure
1.CHECK COMBINATION METER INPUT SIGNAL
Select the "Data Monitor" for the "METER/M&A" and check the "BUZZER" monitor
value.
Is the inspection result ...
