Nissan Rogue Service Manual: C1704, C1705, C1706, C1707 low tire pressure

Nissan Rogue Service Manual / Suspension / Road Wheels & Tires / DTC/circuit diagnosis / C1704, C1705, C1706, C1707 low tire pressure

DTC Logic

NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.

Activate and display TPMS sensor IDs
Display tire pressure reported by the TPMS sensor
Read TPMS DTCs
Register TPMS sensor IDs

DTC DETECTION LOGIC

DTC	Display Item	Malfunction Detected Condition	Possible Cause
C1704	LOW PRESSURE FL	Front LH tire pressure drops to 187.5 kPa (26.5 psi) or less.	Low tire pressure Tire pressure sensor
C1705	LOW PRESSURE FR	Front RH tire pressure drops to 187.5 kPa (26.5 psi) or less.
C1706	LOW PRESSURE RR	Rear RH tire pressure drops to 187.5 kPa (26.5 psi) or less.
C1707	LOW PRESSURE RL	Rear LH tire pressure drops to 187.5 kPa (26.5 psi) or less.

DTC CONFIRMATION PROCEDURE

1.PERFORM SELF DIAGNOSTIC RESULT

With CONSULT

Check tire pressure for all wheels and adjust to the specified value. Refer to WT-65, "Tire Air Pressure".
Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
Perform Self Diagnostic Result.

Is DTC C1704, C1705, C1706, or C1707 detected? YES >> Proceed to WT-24, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.

Activate and display TPMS sensor IDs
Display tire pressure reported by the TPMS sensor
Read TPMS DTCs
Register TPMS sensor IDs

1.TIRE PRESSURE SENSOR ID REGISTRATION

Perform tire pressure sensor ID registration. Refer to WT-21, "Work Procedure".

Can the tire pressure sensor ID registration be completed? YES >> GO TO 2.

NO >> Replace applicable tire pressure sensor. Refer to WT-61, "Removal and Installation".

2.CHECK TIRE PRESSURE

Check the air pressure of all wheels. Refer to WT-65, "Tire Air Pressure".

Is the inspection result normal?

YES >> Perform DTC CONFIRMATION PROCEDURE again. Refer to WT-24, "DTC Logic".

NO >> GO TO 3.

3.CHECK TIRE PRESSURE SIGNAL

With CONSULT

Adjust tire pressure for all wheels to the specified value. Refer to WT-65, "Tire Air Pressure".
Select “AIR PRESSURE MONITOR” of “BCM” Data Monitor.
Check that the air pressures match the specified value.

Monitor item	Displayed value
AIR PRESS FL	Approximately equal to value indicated on tire gauge for front LH tire
AIR PRESS FR	Approximately equal to value indicated on tire gauge for front RH tire
AIR PRESS RR	Approximately equal to value indicated on tire gauge for rear RH tire
AIR PRESS RL	Approximately equal to value indicated on tire gauge for rear LH tire

Is the inspection result normal? YES >> Inspection End.

NO >> Repair or replace malfunctioning components.

DTC/circuit diagnosis

...

C1708, C1709, C1710, C1711 transmitter (no data)

DTC Logic NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information. Activate and dis ...

Other materials:

P1715 input speed sensor
Description ECM receives input speed sensor signal from TCM through CAN communication line. ECM uses this signal for engine control. DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting conditio P1715 IN PULY SP ...

DTC/circuit diagnosis
U0428 STEERING ANGLE SENSOR DTC Logic DTC DETECTION LOGIC CONSULT Display DTC Detection Condition Possible Cause ST ANG SEN CALIB [U0428] Predictive course line center position adjustment of steering angle sensor is incomplete. Adjust predictive cours ...

Preparation
Special Service Tool The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name Description — (J-39570) Chassis Ear Locating the noise — (J-46534) Trim Tool Set Removing ...