Nissan Rogue Owners Manual: Cold weather driving

Nissan Rogue Owners Manual / Starting and driving / Cold weather driving

Freeing a frozen door lock

To prevent a door lock from freezing, apply deicer through the key hole. If the lock becomes frozen, heat the key before inserting it into the key hole, or use the NISSAN Intelligent Key®.

Antifreeze

In the winter when it is anticipated that the temperature will drop below 32°F (0°C), check the antifreeze to assure proper winter protection. For additional information, refer to “Engine cooling system” in the “Maintenance and do-it-yourself” section of this manual.

Battery

If the battery is not fully charged during extremely cold weather conditions, the battery fluid may freeze and damage the battery. To maintain maximum efficiency, the battery should be checked regularly. For additional information, refer to “Battery” in the “Maintenance and do-it-yourself” section of this manual.

Draining of coolant water

If the vehicle is to be left outside without antifreeze, drain the cooling system, including the engine block. Refill before operating the vehicle.

For additional information, refer to “Changing engine coolant” in the “Maintenance and do-ityourself” section of this manual.

Tire equipment

SUMMER tires have a tread designed to provide superior performance on dry pavement.
However, the performance of these tires will be substantially reduced in snowy and icy conditions. If you operate your vehicle on snowy or icy roads, NISSAN recommends the use of MUD & SNOW or ALL SEASON TIRES on all four wheels. Please consult a NISSAN dealer for the tire type, size, speed rating and availability information.
For additional traction on icy roads, studded tires may be used. However, some U.S.
states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires.

Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires.

Tire chains may be used. For additional information, refer to “Tire chains” in the “Maintenance and do-it-yourself” section of this manual.

Special winter equipment

It is recommended that the following items be carried in the vehicle during winter:

A scraper and stiff-bristled brush to remove ice and snow from the windows and wiper blades.
A sturdy, flat board to be placed under the jack to give it firm support.
A shovel to dig the vehicle out of snowdrifts.
Extra washer fluid to refill the windshieldwasher fluid reservoir.

Driving on snow or ice

WARNING

Wet ice (32°F, 0°C and freezing rain), very cold snow or ice can be slick and very hard to drive on. The vehicle will have much less traction or “grip” under these conditions. Try to avoid driving on wet ice until the road is salted or sanded.
Whatever the condition, drive with caution.
Accelerate and slow down with care. If accelerating or downshifting too fast, the drive wheels will lose even more traction.
Allow more stopping distance under these conditions. Braking should be started sooner than on dry pavement.
Allow greater following distances on slippery roads.
Watch for slippery spots (glare ice).
These may appear on an otherwise clear road in shaded areas. If a patch of ice is seen ahead, brake before reaching it. Try not to brake while on the ice, and avoid any sudden steering maneuvers.
Do not use the cruise control on slippery roads.
Snow can trap dangerous exhaust gases under your vehicle. Keep snow clear of the exhaust pipe and from around your vehicle.

Engine block heater (if so equipped) (Canada only)

Engine block heaters are used to assist with cold temperature starting.

The engine block heater should be used when the outside temperature is 20°F (-7°C) or lower.

WARNING

Do not use your engine block heater with an ungrounded electrical system or a 2-pronged adapter. You can be seriously injured by an electrical shock if you use an ungrounded connection.
Disconnect and properly store the engine block heater cord before starting the engine. Damage to the cord could result in an electrical shock and can cause serious injury.
Use a heavy-duty 3-wire, 3-pronged extension cord rated for at least 10 A. Plug the extension cord into a Ground Fault Interrupt (GFI) protected, grounded 110-VAC outlet. Failure to use the proper extension cord or a grounded outlet can result in a fire or electrical shock and cause serious personal injury.

To use the engine block heater:

Turn the engine off.
Open the hood and unwrap the engine block heater cord.
Plug the engine block heater cord into a grounded 3-wire, 3-pronged extension cord.
Plug the extension cord into a Ground Fault Interrupt (GFI) protected, grounded 110- volt AC (VAC) outlet.
The engine block heater must be plugged in for at least two to four hours, depending on outside temperatures, to properly warm the engine coolant. Use an appropriate timer to turn the engine block heater on.
Before starting the engine, unplug and properly store the cord to keep it away from moving parts.

Hill start assist system

Hill start assist system WARNING Never rely solely on the hill start assist system to prevent the vehicle from moving backward on a hill. Always drive carefully and a ...

In case of emergency

...

Other materials:

Front door glass
Exploded View Front door Front regulator Front power window motor Front door glass rear run Front door glass front run Front door glass Front door glass rubber run Removal and Installation REMOVAL Remove the front door finisher. Refer to INT-15, "Remov ...

How to use the remote keyless entry function
The remote keyless entry function can operate all door locks using the remote keyless function of the Intelligent Key. The remote keyless function can operate at a distance of 33 ft (10 m) away from the vehicle. The operating distance depends upon the conditions around the vehicle. The remot ...

Symptom diagnosi
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING NVH troubleshooting - engine noise Valve mechanism Intake and exhaust valve Water pump Timing chain Drive belt Rotation mechanism Tappet noise Camshaft bearing noise &nb ...