Nissan Rogue (T33) 2021-Present Owner’s Manual & User Guide: Forward-facing child restraint installation using LATCH
Basic information
For proper installation of a forward-facing child restraint in your Nissan Rogue, carefully review all Warnings and Cautions in the “Child safety” and “Child restraints” sections before beginning.
Do not use the lower anchors if the combined weight of the child and restraint exceeds 65 lbs (29.5 kg). If the combined weight is higher than 65 lbs (29.5 kg), install the restraint using the Nissan Rogue seat belt instead of the LATCH anchors. Always follow the child restraint manufacturer’s installation instructions.
Follow these steps to install a forward-facing child restraint using the LATCH system:
1. Position the child restraint on the seat.
Always follow the instructions provided by the child restraint manufacturer.
Forward-facing web-mounted - step 2
2. Secure the restraint’s LATCH attachments to the lower anchors. Check carefully to ensure the attachment is fully seated and locked onto the anchor points of your Nissan Rogue.
If equipped with a top tether strap, route the strap and attach it to the appropriate tether anchor. See “Installing top tether strap.” Do not install child restraints requiring a top tether in seating positions without a tether anchor.
Forward-facing rigid-mounted - step 2
3. Ensure the back of the child restraint rests firmly against the vehicle seatback.
If needed, adjust or remove the head restraint/headrest to achieve proper fitment. If removed, store it securely and reinstall it once the child restraint is removed. See “Head restraints/headrests” for details.
If the seating position has a non-adjustable head restraint/headrest that interferes with correct installation, choose another seating position or a different restraint.
Forward-facing - step 4
4. If the restraint uses webbing-mounted attachments, remove extra slack by pressing downward and rearward firmly in the center of the restraint using your knee. This compresses the seat cushion and seatback of your Nissan Rogue for a tighter fit.
5. Tighten the top tether strap according to the manufacturer’s instructions.
Forward-facing - step 6
6. Test the installation prior to placing the child in the restraint. Hold the child restraint near the LATCH attachment path and push it from side to side.
The restraint should not move more than 1 inch (25 mm) sideways. Pull it forward to ensure the LATCH anchors hold it securely. If it is loose, tighten the LATCH attachments or try another seating location. Some restraints may not fit all vehicles.
7. Confirm the restraint is properly secured before each use. If loose, repeat steps 1–6.
Rear-facing child restraint installation using the seat belts
WARNING
The three-point seat belt with Automatic Locking Retractor (ALR) must be used when installing a child restraint. If the ALR mode is not used, the restraint may not be properly secured and co ...
Installing top tether strap
WARNING
Child restraint anchorages are designed only for loads from correctly installed child restraints. Never attach adult belts or other equipment to them. Damage could compromise safety and l ...
Other materials:
B0098 front door satellite sensor RH
DTC Logic
DTC DETECTION LOGIC
With CONSULT
CONSULT name
DTC
DTC detecting condition
Repair order
DOOR SATELLITE SENSOR RH
[SENSOR FAIL]
B0098
Front door satellite sensor RH has malfunctioned.
Refer to SRC-72, "Diagnosis Procedure".
...
How to enable/disable the sonar system
Steering-wheel-mounted control (left side)
Vehicle information display
The sonar system activates automatically when the ignition switch is in the ON position and the shift lever is in D (Drive) or R (Reverse).
To set up sonar system functions, follow these steps:
1. Press the
button un ...
Infants
Infants up to at least 1 year old should be placed in a rear-facing child restraint.
NISSAN recommends that infants ride in child restraints that comply with Federal Motor Vehicle Safety Standards or Canadian Motor Vehicle Safety Standards. Choose a restraint that fits your Nissan Rogue properly ...
